Circuit Theory/Example70

$V_{s1}=\frac{\sqrt{2}}{6}\cos (t+\frac{\pi }{4})$

$V_{s2}=\cos (t+\frac{\pi }{3})$

${𝕍}_{s1}=\frac{1}{6}(1+j)$

${𝕍}_{s2}=\frac{1}{2}(1+j\sqrt{3})$

The series components can be lumped together .. which simplifies the circuit a bit.

Node Analysis

File:Example70mupad.png

mupad and matlab /code/ for all the work below

$\frac{{𝕍}_{s1}-{𝕍}_a}{5}-{𝕍}_a-\frac{{𝕍}_a+{𝕍}_{s2}}{j\sqrt{3}}=0$

${𝕍}_a=-0.42063+j0.065966$

Mesh Analysis

$i_1-i_2-V_{s1}+5*i_1=0$

$i_{2}j\sqrt{3}-V_{s2}+i_2-i_1=0$

$i_3=i_1-i_2$

Solving

$i_3=-0.42063+j.065966$

Which is the same as the voltage through the 1 ohm resistor.

Thevenin voltage

Make ground the negative side of $V_{s2}$, then:

$V_{th}=V_A-V_B$

$V_{th}=i*j\sqrt{3}-V_{s2}$

$V_{th}=\frac{V_{s1}+V_{s2}}{5+j\sqrt{3}}*j\sqrt{3}-V_{s2}$

Solving

$V_{th}=-0.747977-j0.5492$

Norton Current

• 
  short out the load
• 
  split into two circuits so can use superposition
• 
  half the circuit is shorted out by shorting the voltage sources

$i_n=i_1-i_2=\frac{V_{s1}}{5}-\frac{V_{s2}}{j\sqrt{3}}$

$i_n=-0.4667+j0.3220$

Thevenin/Norton Impedance

short voltage sources, open current sources, remove load and find impedance where the load was attached

$Z_{th}=\frac{1}{\frac{1}{5}+\frac{1}{j\sqrt{3}}}=0.537+j1.5465$

check

$Z_{th}=\frac{V_{th}}{I_n}=0.537+j1.5465$

yes! they match

Evaluate Thevenin Equivalent Circuit

Going to find current through the resistor and compare with mesh current

$i=\frac{V_{th}}{Z_{th}+1}=-0.42063+j0.06599$

yes! they match

Find Load value for maximum power transfer

$Z_L=z_{th}^{*}=0.537-j1.5465$

Find average power transfer with Load that maximizes

$Z_{th}+Z_L=0.537*2$

$P_{avg}=\frac{Re(V_{th}{)}^2}{Z_{th}+Z_L}=\frac{\sqrt{0.747977^2+0.5492^2}}{2*0.537}=0.8037watts$

Simulation

The circuit was simulated. A way was found to enter equations into the voltage supply parameters which improves accuracy:

• 
  type sqrt(3) instead of a numeric approximation
• 
  added pi/2 to convert from cos to sin sources

To compare with the results above, need to translate the current and voltage through the resistor into the time domain.

Period

Period looks right about 6 seconds ... should be:

$T=\frac{1}{f}=\frac{2*\pi }{w}=2*\pi =6.2832$

Current

Current through 1 ohm resistor, once moved into the time domain (from the above numbers) is:

$i(t)=0.4258*cos(t+171^{\circ })$

From the mesh analysis, the current's through both sources were computed:

$i_{s1}=0.1192*cos(t+9.72^{\circ })$

The magnitudes are accurate, they are almost π out of phase which is can be seen on the simulation.

Voltage

The voltage is the same as the current through a 1 ohm resistor:

$v(t)=0.4258*cos(t+171^{\circ })$

The voltage of the first (left) source is:

$V_{s1}=\frac{\sqrt{2}}{6}cos(t+\frac{pi}{4})=0.2357*cos(t+45^{\circ })$

The magnitudes match. The voltage through the source peaks before the current because the first source sees the inductor.

The voltage through the resistor should peak about 171 - 45 = 126° before the source ... which it appears to do.